Smc barricade 2804 manual

Determine which browser you use and follow the appropriate steps. By default, the password is smcadmin. The default is case sensitive. Making Configuration Changes Configurable parameters have a dialog box or a drop-down list. The first item is Time Zone. For accurate timing of client filtering and log events, you need to set the time zone. Select your time zone from the drop-down list.

For a cable modem connection see the following page. Page 41 Cable Modem After selecting Cable Modem as the Broadband Type, a message will appear stating that your data has been successfully saved.

Page 42 Configuring the Wireless Barricade g Router Enter a Maximum Idle Time in minutes to define a maximum period of time for which the Internet connection is maintained during inactivity. If the connection is inactive for longer than the Maximum Idle Time, it will be dropped. Default: 10 Enable the Auto-reconnect option to automatically re-establish the connection as soon as you attempt to access the Internet again. Click NEXT to complete the setup.

Dynamic DNS provides users on the Internet with a method to tie their domain name to a computer or server. This information is used for log entries and client access control. By default, there is no password. For security you should assign one before exposing the Router to the Internet. Passwords can contain from 3—12 alphanumeric characters and are not case sensitive. Page 47 Remote Management Remote Management allows a remote PC to configure, manage, and monitor the Router using a standard web browser.

Check Enable and enter the IP address of the remote host. Note: If you specify 0. Use this address when registering for Internet service, and do not change it unless required by your ISP. The Service Name is normally optional, but may be required by some service providers. You may need a fixed address if you want to provide Internet services, such as a web server or FTP server. Enter those addresses in this screen. For home networks this may be set to Forever, which means there is no time limit on the IP address lease.

Be sure you configure all of your clients to the same values. This should be set to the same value as the other wireless devices in your network. The lower the data rate, the longer the transmission distance. Default: Fully Automatic. Default: 6 Note: The available channel settings are limited by local regulations. WEP mode: You can choose disabled, bit or bit encryption. Key Provisioning: Select a key type of static key or dynamic key. Choose a key ID from the drop-down list or accept the default key.

If you use encryption, configure the same keys used for the Router on each of your wireless clients. Note that Wired Equivalent Privacy WEP protects data transmitted between wireless nodes, but does not protect any transmissions over your wired network or over the Internet. Page 66 Configuring the Wireless Barricade g Router Virtual Server If you configure the Router as a virtual server, remote users accessing services such as web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses.

Page 67 Special Applications Some applications, such as Internet gaming, videoconferencing, Internet telephony and others, require multiple connections. If you need to run applications that require multiple connections, use the following screen to specify the additional public ports to be opened for each application. You can define up to 32 clients using the MAC address filtering table.

When enabled only the MAC addresses entered will have access to your network. These rules can then be used to configure more specific Access Control. Click Add Schedule Rule. Define the settings for the schedule rule as shown on the following screen. This is a way of ensuring that all communications are initiated by the recipient computer and are taking place only with sources that are known and trusted from previous interactions.

Page 80 Configuring the Wireless Barricade g Router If you have a client PC that cannot run an Internet application properly from behind the firewall, then you can open the client up to unrestricted two-way Internet access. Default: Disable Domain Name — Page Tools TOOLS Use the Tools menu to back up the current configuration, restore a previously saved configuration, restore factory settings, update firmware, and reboot the Router.

Page 84 Configuring the Wireless Barricade g Router Firmware Upgrade Use this screen to update the firmware or user interface to the latest versions. Download the upgrade file from the SMC web site www. In the Upgrade Target field, choose Firmware.

Click OK to reboot. The reset will be complete when the power LED stops blinking. Note: If you use the Reset button on the front panel, the Router performs a power reset. If the button is depressed for over five seconds, all the LEDs will illuminate and the factory settings will be restored.

This is because these steps and screen shots were created in Windows Windows Millennium Edition is very similar, but not identical, to Windows Select the destination folder and click on the Next button.

The setup program will then begin to install the programs into the destination folder. Select the Program Folder that will contain the program icon for uninstalling the port monitor, and then click Next.

Page 90 Configuring Printer Services 6. Follow the prompts to add a local printer to your system. Page 92 Configuring Printer Services 3. Select the monitored port. Click Next in the Add Printer Wizard dialog box.

Page 94 Configuring Printer Services 4. Then click Next in the Add Printer Wizard dialog box. Below is an outline on how to configure the LPR port on a Windows machine; Click the Next button to create a new printer port. To start this new installation wizard click the Next button.

Provide the appropriate IP and Port name information for your new Printer port. If you are using default settings on the router you can use the following information: Printer Name or IP Address: Page 98 Configuring Printer Services Click the Next button to continue. On the next dialog box, under the Device type choose the Custom option. Then click the Settings… button to input the Specific Barricade Printer port information Page Configuring Printer Services Seite 17 Passaggio Esecuzione dei collegamenti Passaggio Seite 18 Configurare un computer Macintosh 2.

Seite 20 2. Seite 21 Steg Seite 22 2. Seite 23 Netscape Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the 1. SMC is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. Seite 1 drucken Dokument drucken 25 Seiten. Lesezeichen umbenennen. Anmelden ODER.

Noch keinen Account? Registrieren Sie sich jetzt! Passwort vergessen? Anleitung hochladen. Von PC hochladen. Von URL hochladen.