Hampton bay ceiling fan with light installation instructions

That is always the best way to go about. In the event you cannot find the original documentation that came with the fan purchase, then try taking a look on Google for your model. Not sure of your model?

You can find it on the bottom housing or sometimes inside of the housing of the fan. The below instructions are in point form. They were made while installing a Hampton Bay San Marino ceiling fan.

Some of this information may be useful for installing other ceiling fans as well — not just the San Marino, as many installation steps are generic amongst Hampton Bay Ceiling Fans. This dual use light kit can work in two ways. The first way is, the light kit can attach directly to the ceiling. The second method, is it can attach to a ceiling fan directly. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for website owners to earn advertising fees by advertising and linking to amazon.

As an Amazon Associate, this website earns from qualifying purchases. Loosen the two screws in the collar on top of the motor assembly. Remove the canopy ring from the canopy by turning the ring to the right until it unlocks. Remove the mounting plate from the canopy by loosening the four screws on the top of the canopy.

Remove the two non-slotted screws and loosen the slotted screws. This will enable you to remove the mounting plate. Route the wires exiting the top of the fan motor through the canopy ring. Make sure the slot openings are on top. Align the holes at the bottom of the down-rod with the holes in the collar on top of the motor housing. Insert the bolt through the holes in the collar and downrod. Be careful not to jam against the wiring inside the downrod. Insert clevis pin and bend to ensure security.

Tighten the two screws on the collar on top of the motor housing. Part 2. Pass the volt supply wires through the center hole in the ceiling mounting plate. Install the ceiling mounting plate on the outlet box. Slide the mounting plate over the two screws provided with the outlet box.

When using close-to-ceiling mounting, it is important that the mounting plate be level. If necessary, use leveling washers not included between the mounting plate and the outlet box. Note that the flat side of the mounting plate is toward the outlet box. Lift the assembly up to the ceiling mounting plate carefully. If you are using close-to-ceiling mounting, hang the fan on the hook provided by utilizing one of the holes at the outer rim of the ceiling canopy.

If using standard mounting, seat. Make sure the tab on the mounting plate socket is properly seated in the groove in the hanger ball. Part 3. Disconnect the power. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.

Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. Connect the ground conductor of the v supply this may be a bare wire or a wire with green insulation to the green ground lead s of the fan. Connect the fan motor white wire to the supply white neutral wire using a wire nut.

Connect the fan motor black wire to the sup-ply black hot wire using a wire nut. Spread the wires apart. The green and white wires are on one side of the outlet box and the black wire is on the other side. The bare copper wire from the electrical box is attached to this green wire or screw. The black wire from the electrical box attaches to the black wire from the ceiling fan.

If there is no toggle switch on the wall for operating the light and ceiling fan separately then place the blue and black wires from the ceiling fan and electrical box together. If you have the toggle switch to operate the ceiling fan and light separately then match up the red wire and blue wire together.

This is a common problem with many different reasons, so we need to approach it logically looking at all the possible reasons. For this, you will need a noncontact voltage meter. The first thing to do is to check for possible damage to the ceiling fan light sockets. Here is the step by step process for doing this.

If the problem is still not resolved then the next stage will be to check the wall switch wiring for the ceiling fan. To do this follow these easy steps below:. If you still have no lights working then the next step is to check the wire connections for the ceiling fan. If you are still having problems than another possible suggestion would be to replace the pull chain that turns the light on.

Check online or your manual to see how to do this. However please be mindful that the existing electrical box will not be strong enough to support the additional weight of a ceiling fan. You will need to either use a rated hanger and box to fix the ceiling fan securely between joists. After doing some research on this question I found that the simple is answer is no you cannot add a light kit to any ceiling fan.

The reason is pretty straightforward. If your ceiling fan has no housing assembly to take a light kit then you will NOT be able to add a light kit. No, you will need to ensure you either have an existing light fixture or fan in place. If you do not, then you will need to run some cables to an existing power source which would require the services of a qualified electrician.